Yanhua Mini ACDP BMW FRM Footwell Module 0L15Y 3M25J Read/Write
Supports BMW FRM Footwell Module 0L15Y EEPROM FLASH Read/Write Supports BMW FRM 3M25J EEPROM, D-FLASH, P-FLASH Read/Write
Top 4 Reasons To get YANHUA ACDP FRM Module: 1.Integrated data reading/writing, data conversion in one programmer; 2.no need to write other cars’ data; 3.no need to coding. 4.Simple and efficient.
Confirmed: BMW Mini Cooper remote programming can be done by Yanhua Mini ACDP programmer.
If it is CAS3, ACDP can do via OBD, if it is CAS3+, ACDP can do only after dismantling the CAS3+ and program new key using interface board.
Method 1: ACDP program remote on Mini Cooper using the interface board
Method 2: ACDP program remote on Mini Cooper via OBD Obd port: located in the driver side, on the left Connection:Mini ACDP is connected to the car, through OBD The test:
Insert the key
Run Mini ACDP application on the mobile
Run BMW module programming
Select CAS3/CAS3+
OBD mode
Immobilizer
Step 1: read CAS data
Step 2: generate a dealer key/program a key
Step 3: write new key data into CAS Step 1: read CAS data
ACDP is gonna to read CAS data
Pop-up: Take out the key and wait for 5 min.
If the key without ignition-start function, take the key outside the car, 3m away
Read immo data successfully
File (CAS3_ORGKEYxxxx.bin) has been backup.
Upload bin file
Save the immo data to generate a dealer key
Step 2: generate a dealer key/program a key Yanhua ACDP is gonna to add a new key
Check the connection of BAV adapter
Prepare a blank key
Choose the correct bin file with immo data
Here select Key 5 to program
Note: Gray number is used for the original key
The black numbers are available for calculation
Pop-up: It’s one of keys available. If you enable a new key, the original key will not work anymore.
Select a method to generate a dealer key
Here: add a new key with a working key
Check if the key is a smart one or not. If yes, you have to choose Key 1-3
Here: it’s not a smart key
Go to add a new key
Insert the blank key to program
Programming...
ACDP successfully programmed a new key
The generated CAS data includes the new key info.
Pls go to write new data into CAS
File is backup
Upload file (will be written into CAS...DLRKEY...bin)
Step 3: write new key data into CAS
Insert the original key before you’re gonna to write data into CAS
Go to update key data
Select the correct bin file
Select a method to generate a dealer key
Here: add a new key with a working key
Updating new immo data
(writing the key data into CAS)
Immo data is updated successfully.
Backup data
Please install the CAS into the car and try the new key to start.
The ELV is faulty; you should synchronize it
Go to special function, synchronize CAS and ELV
Synchronize CAS and ELV successfully
Backup data
Insert the new key again to start
The dashboard works well, without fault codes
Confirmed: Yanhua Mini ACDP is allowed to bound in more than one mobile Phone, not only one phone. But only in one mobile phone at the same time, if you want to bound another one mobile phone, this former one needs to be unbound.
You can use your mobile phone to unbound by yourself, or you can press the "Reset" button on the Yanhua Mini ACDP to unbound.
Mobile phone bound to Yanhua Mini ACDP Procedure:
->Open the Bluetooth and connect the WI-FI
->Open the ACDP on your phone and click setting as the following icon
->Click "Initial use settings"
->Following the directions:
press and hold the "SET"button ,after 7 seconds,ACDP 's buzzer sounds"Di~~~" and finish initial programming process
->Choose the Bluetooth device
->Enter the password of WI-FI, the clic Start configuration